lite-on dcc release bns-od-fc001/a4 lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto led displayproduct data sheetLSHD-A103 spec no. :ds30-2002-148effective date: 06/03/2017 revision: b
1 / 6 part no. : LSHD-A103 bns-od-fc002/a4 led display LSHD-A103 led display LSHD-A103 rev description by date - above data for pd and customer tracking only - new thomas yu 12/31/2002 a update rev in system reo lin 04/27/2011 b update rev in system erin cheng 05/26/2017
2 / 6 part no. : LSHD-A103 bns-od-fc002/a4 led display LSHD-A103 1. description the LSHD-A103 is a 0.3 inch (7.62 mm) digit height single-digit display. this device uses alingap red led chips (alingap epi on gaas substrate). the display has light gray face and white segments. 1.1 features 0.3 inch (7.62 mm) digit height continuous uniform segments low power requirement excellent characters appearance high brightness & high contrast wide viewing angle solid state reliability categorized for luminous intensity. lead-free package(according to rohs) 1.2 device part no description alingap red common cathode rt. hand decimal LSHD-A103
3 / 6 part no. : LSHD-A103 bns-od-fc002/a4 led display LSHD-A103 2. package dimensions notes : 1. all dimensions are in millimeters. tolerances ar e 0.25 mm (0.01) unless otherwise noted 2. pin tips shift tolerance is 0.4 mm 3. foreign material on segment Q 10mil 4. ink contamination (surface) 20mils Q 5. bubble in segment Q 10mil 6. bending Q 1% of reflector length
4 / 6 part no. : LSHD-A103 bns-od-fc002/a4 led display LSHD-A103 3. internal circuit diagram 4. pin connection no connection 1 common cathode 2 anode f 3 anode g 4 anode e 5 anode d 6 common cathode 7 anode dp 8 anode c 9 anode b 10 anode a
5 / 6 part no. : LSHD-A103 bns-od-fc002/a4 led display LSHD-A103 5. rating and characteristics 5.1. absolute maximum rating at ta=25c parameter maximum rating unit power dissipation per segment 70 mw peak forward current per segment ( 1/10 duty cycle, 0.1ms pulse width ) 90 ma continuous forward current per segment derating linear from 25c per segment 25 0.28 ma ma/c operating temperature range -35c to +105c storage temperature range -35c to +105c solder condition: 1/16 inch below seating plane for 3 seconds at 260c or temperature of unit (during assembly) not over max. temperature rating above 5.2.electrical / optical characteristics at ta=25c parameter symbol min. typ. max. unit test condition average luminous intensity per segment iv 200 3400 692 9000 m cd if=1ma if=10ma peak emission wavelength l p 650 nm if=20ma spectral line half-width dl 20 nm if=20ma dominant wavelength l d 639 nm if=20ma forward voltage per chip vf 2.1 2.6 v if=20ma reverse current per segment (*2) ir 100 m a vr=5v luminous intensity matching ratio (similar light area) iv-m 2:1 if=10ma notes : 1. luminous intensity is measured with a light sens or and filter combination that approximates the cie (commission international de leclariage) eye-response curve 2. reverse voltage is only for ir test. it cannot c ontinue to operate at this situation
6 / 6 part no. : LSHD-A103 bns-od-fc002/a4 led display LSHD-A103 5.4. typical electrical / optical characteristics c urves (25 c ambient temperature unless otherwise noted)
|
